A Need For Machining
Machining For Every Need
The following are emails I received from customers that purchased our "Universal Sight Pusher."
These are unedited emails, copied and pasted to this page to help you make an informed decision.
Thank you for chosing and making our US Patented "Universal Sight Pusher" the best tool money can buy.
US Patent #8910413
As always, Thank You for your time and Thank You for your business and support.
There are tons of reviews online for my tool and the ones that have stolen my design, read up and see THIS IS the BEST tool your money can buy
Hillwig Tool LLC • Meadville, PA 16335
- On Thu 11/7/2013 2:19 PM Chip L. wrote:
Got the tool today. All I can say is WOW... you sure take pride in your work! I have worked in machine shops as an EE over the years (pretty much a 'closet' machinist) and made many tools and other things, but this thing is detailed out to the max!
I don't even want to use the pusher as it looks so good, I'm afraid I might put a scratch on it ;)
Very well built. And thank you very much for the extra side screw. I'll keep you posted on how it goes, here we go... on from 1911 days and into the world of SA XD's and the rest.
Will definitely promote your tool, and how prompt the shipping was and your good nature! Progress pictures to follow... wish me luck.
Again, Thank You Jim!
Cheers - and stay safe out there,
- On Aug 11, 2013, at 6:51 PM, Robbin P. wrote:
just a quick note ...
I received the pusher, and have changed out the sights on 3 XDs ... the first two were a piece of cake ... the third one proved to b one of the Xds that I was told about ... had to put a small pipe on the hex wrench to get enough leverage to get it to move ... and move it did, and it changed it out, in spite of the difficulty with both front and back sights ... the only thing that happened was the aluminum block that pushes on the sight, was dented to the point where I had to clean up the pusher block, because of the metal shavings that had flaked off of the block ... so it does work even on the extremely difficult problematic sights ... but it looks like I may need to replace the block after a couple more of the more difficult ones that I may encounter ... and u did give me a extra block ... so just wanted to give u some feedback regarding your product ... thanx again,
could not have changed out these sights with anything less than the quality of the design of your tool ... warm regards,
- On Feb 10, 2013, at 10:51 AM, Jerry S. wrote:
I just wanted to say thank you! I used the sight pusher last night to remove the factory sights and install TruGlo TFOs on my XDM and XDS. It worked perfectly. Wow - what a difference it makes to have the right tool for the job. I have never installed sights before and I had zero problems. You have truly made a better mousetrap. Best $120 I have spent in a long time.
- On Sat 2/2/2013 12:59 PM, Colt K wrote: Hi I have a question about the sight pusher.....I have read that most sight tools have issues with clamping the angled sides on XDm slides and they will rock when pressure is applied....Does your pusher with the swivel bolt minimize this?
My Answer Was: YES! Thanks Jim
- On Fri 2/1/2013 10:36 PM, Randy Wrote:
Just used the sight pusher for the first time tonight. Nice stuff. There is a thread I posted on XD Talk forum.
If I had 1 thing I could change it would be putting a pusher block on each side of the tool. I realize that you would have to make the tool wider for that to be a possibility, but it gets to be a bit of a pain bolting everything down, unbolting it, removing the slide to set the ram and block up on the other side then bolting it all back down again. I wasn't sure if I cold punch the guide rod for the block out without damaging the threads so I didn't do that. Anyhow - not complaining, just offering my unsolicited $.02.
Other than that, it worked GREAT.
Thanks again for all the great service. I hope you get some good business out of my thread. I have 2 more handguns I'll be using this with and possibly 1 more on the way. Looking forward to it.
- On Thu 1/31/2013 1:10 AM, Vince Wrote: Mr Hillwig,
I just got the pusher in today's mail, and it worked great! Thanks! I've got my new sights on and I'm ready to go target practice thanks to you!
- On Thu 1/31/2013 12:42 AM, Mike Z. Wrote:
I just wanted to thank you for making such a great tool. I was concerned about snapping off the front sight but it came off smooth and clean. I am amazed at the amount of pressure it took. Now I have a brand new set of tritium sights on my XD40.
- On Mon 1/28/2013 2:53 PM, Buck Wrote:
I just got the sight pusher (like 20 minutes ago). I already put my night sights on my XD-s .45!!
Thank you so much for an awesome tool at an awesome price! I can sell my Glock only rear sight tool now.
Very easy to use, didn't even use grease and it didn't mar up my new Trijicions.
- On Mon 2/18/2013 6:01 PM, Benny S Wrote:
I have used your sight pusher to install front and rear sights on four XDMs and front sights on two Rugers, an SR9 and an SR45.
With the sight manufacturers charging 20-35 dollars per sight plus shipping costs you can't go wrong to buy this tool and install
them yourself. I also let a friend use the tool to install sights on his Glock. I set it up on a Springfield 1911 just to see it it would
work and it looks like it will work fine. If it is possible you will do sights on more than one gun buy the tool.